Anonymous

G/046 Lighting Rig: Difference between revisions

From YSTV Documentation Wiki
no edit summary
No edit summary
Line 5: Line 5:


== Dimmers ==
== Dimmers ==
Pulsar status dimmers: (2 of)
Strand 6pack Dimmer
* 8-pin Din analogue signal in, 0-10v
*DMX512 control via 5pin XLR. Pass Through
* With pre-heat (good for not shocking cold bulbs if they suddenly get turned on, this increases lamp life.
*6 10A channels, each with dual 15A sockets
* 6 5amp channels each.
*32A Power Cable
* IEC plugs on flying leads out.
* If they're buzzing, they're happy!
**'''faults'''
***Top dimmer channel 3, Likes to turn itself on to around 30% after a while. i.e. It's level can be raised, but not lowered beyond 30%. The time taken for this fault to appear can be minutes, or hours. It does not seem to be linked to heat - on 18/02/2010 the behaviour was observed when warm, and cold (given a break for 1/2 hour before retrying). This dimmer channel corresponds on the desk to what was "old channel I" - i.e. pre 18/02/2010 it would have been bottom dimmer channel 3..
***Bottom dimmer channel 3, The transistor/triac looks fried and has continuity between the emitter and collector, also two medium-power 270 Ohm resistors have physically split. This dimmer channel corresponds on the desk to what was "old channel C" - i.e. pre 18/02/2010 it would have been top dimmer channel 3..




Line 32: Line 27:


== Desk ==
== Desk ==
Zero88 Sirius24 (2 of)
Strand 200 plus
see [[Technical:Lighting Desk|Lighting Desk]]
see [[Technical:Lighting Desk|Lighting Desk]]


Line 196: Line 191:
'''other stuff'''
'''other stuff'''
* chinagraph pencils for writing silly (and possibly useful) messages on gels.
* chinagraph pencils for writing silly (and possibly useful) messages on gels.
==Old/unused Equipment==
This is equipment that is still owned by YSTV and is stored within the studio, but is not currently in use due to newer equipment/incompatibility with current equipment in use.
Pulsar status dimmers: (2 of)
* 8-pin Din analogue signal in, 0-10v
* With pre-heat (good for not shocking cold bulbs if they suddenly get turned on, this increases lamp life.
* 6 5amp channels each.
* IEC plugs on flying leads out.
* If they're buzzing, they're happy!
**'''faults'''
***Top dimmer channel 3, Likes to turn itself on to around 30% after a while. i.e. It's level can be raised, but not lowered beyond 30%. The time taken for this fault to appear can be minutes, or hours. It does not seem to be linked to heat - on 18/02/2010 the behaviour was observed when warm, and cold (given a break for 1/2 hour before retrying). This dimmer channel corresponds on the desk to what was "old channel I" - i.e. pre 18/02/2010 it would have been bottom dimmer channel 3..
***Bottom dimmer channel 3, The transistor/triac looks fried and has continuity between the emitter and collector, also two medium-power 270 Ohm resistors have physically split. This dimmer channel corresponds on the desk to what was "old channel C" - i.e. pre 18/02/2010 it would have been top dimmer channel 3..
***One dimmer is without a power cable - this was due to power cable being needed for the Strand 6pack
Zero88 Sirius24 (2 of)
camera trained, confluence-users, coshh trained, crowd-administrators, domain admins, domain users, jira-administrators, jira-developers, jira-users, ladder trained, lighting trained, stash-users, webdev
392

edits