G/046 Lighting Rig: Difference between revisions

G/046 Lighting Rig (view source)

Revision as of 19:02, 8 January 2013

449 bytes added , 8 January 2013

no edit summary

camera trained, confluence-users, coshh trained, crowd-administrators, domain admins, domain users, jira-administrators, jira-developers, jira-users, ladder trained, lighting trained, stash-users, webdev

392

edits

@@ Line 5: / Line 5: @@
 == Dimmers ==
-Pulsar status dimmers: (2 of)
+Strand 6pack Dimmer
-* 8-pin Din analogue signal in, 0-10v
+*DMX512 control via 5pin XLR. Pass Through
-* With pre-heat (good for not shocking cold bulbs if they suddenly get turned on, this increases lamp life.
+*6 10A channels, each with dual 15A sockets
-* 6 5amp channels each.
+*32A Power Cable
-* IEC plugs on flying leads out.
-* If they're buzzing, they're happy!
-**'''faults'''
-***Top dimmer channel 3, Likes to turn itself on to around 30% after a while. i.e. It's level can be raised, but not lowered beyond 30%. The time taken for this fault to appear can be minutes, or hours. It does not seem to be linked to heat - on 18/02/2010 the behaviour was observed when warm, and cold (given a break for 1/2 hour before retrying). This dimmer channel corresponds on the desk to what was "old channel I" - i.e. pre 18/02/2010 it would have been bottom dimmer channel 3..
-***Bottom dimmer channel 3, The transistor/triac looks fried and has continuity between the emitter and collector, also two medium-power 270 Ohm resistors have physically split. This dimmer channel corresponds on the desk to what was "old channel C" - i.e. pre 18/02/2010 it would have been top dimmer channel 3..
@@ Line 32: / Line 27: @@
 == Desk ==
-Zero88 Sirius24 (2 of)
+Strand 200 plus
 see [[Technical:Lighting Desk|Lighting Desk]]
@@ Line 196: / Line 191: @@
 '''other stuff'''
 * chinagraph pencils for writing silly (and possibly useful) messages on gels.
+==Old/unused Equipment==
+This is equipment that is still owned by YSTV and is stored within the studio, but is not currently in use due to newer equipment/incompatibility with current equipment in use.
+Pulsar status dimmers: (2 of)
+* 8-pin Din analogue signal in, 0-10v
+* With pre-heat (good for not shocking cold bulbs if they suddenly get turned on, this increases lamp life.
+* 6 5amp channels each.
+* IEC plugs on flying leads out.
+* If they're buzzing, they're happy!
+**'''faults'''
+***Top dimmer channel 3, Likes to turn itself on to around 30% after a while. i.e. It's level can be raised, but not lowered beyond 30%. The time taken for this fault to appear can be minutes, or hours. It does not seem to be linked to heat - on 18/02/2010 the behaviour was observed when warm, and cold (given a break for 1/2 hour before retrying). This dimmer channel corresponds on the desk to what was "old channel I" - i.e. pre 18/02/2010 it would have been bottom dimmer channel 3..
+***Bottom dimmer channel 3, The transistor/triac looks fried and has continuity between the emitter and collector, also two medium-power 270 Ohm resistors have physically split. This dimmer channel corresponds on the desk to what was "old channel C" - i.e. pre 18/02/2010 it would have been top dimmer channel 3..
+***One dimmer is without a power cable - this was due to power cable being needed for the Strand 6pack
+Zero88 Sirius24 (2 of)