OB talk:Woodstock 2010: Difference between revisions

From YSTV Documentation Wiki
m (→‎Cable Runs: Partly-done cable run)
m (→‎Cable Runs: A few cat 5 additions)
Line 360: Line 360:


Mains to power cameras, I haven't specifically asked for this but there shouldn't be a shortage of power, given all the mains sockets on the walls anyway.
Mains to power cameras, I haven't specifically asked for this but there shouldn't be a shortage of power, given all the mains sockets on the walls anyway.
All indoor stage video cables to V12'''''2'''''
'''CAT5 ADAPTORS'''
Will probably have the powered one in the hall, and the passive one on the main stage.  This will of course only work if the passive one can send a decent signal all the way to V120 from the main stage.  The distances to the two stages are about equal.
*  Advantages:
**  Powered one receives three signals, we have three cameras on indoor stage, one cat5 to back of hall and out of window towards V122 (avoids having three bncs running across the hall, saves cable length, simplifies run, fewer potential fault points etc.).
**  Main Stage is more important, the passive sender sends one signal on each pair, they're completely isolated as far as I (Malcolm) know.  If one pair develops a problem we still have three good camera signals being sent along the cat5.
**  Is bidirectional, the monitors at the main stage will receive signal, uses one of the less-reliable and lower-quality cat5 pairs rather than a BNC for low-priority monitors.
*  Disadvantages
**  May not be powerful enough to send signal, would prefer signal from mains stage to be good.
More to follow...
'''Comms'''
Mostly still to write down.
'''Main Stage Monitors''' 
Still to write.

Revision as of 15:42, 18 June 2010

--Michael.chislett 11:55, 30 May 2010 (UTC)If I've missed anything, shove it here. discussion here too...

Malcolm's preliminary proposal

I'm not writing it all out again, use this link to see my proposal and comments on the draft version, with suggestions of where to put certain equipment, and justification for some of these locations/applications.

As a definite concensus/decision is made on where or how to use something the current 'permanent' version should be updated.

Any disagreements with anything there then please detail below.


Also can we please soon decide collectively on where howard should go and whether we're doing both 4:3 or only the indoor stage. This is also a presentation/production matter to some extent.

Mike

aspect ratio fun:

  • I think if the clever Nvidia graphics idea doesn't come up with anything by the end of your answeres rubbish (tuesday), we'll have to call it as all 4:3. (aww, I was looking forward to 16:9...).
  • To give us a better chance next year at going widescreen, my suggestion is to also record widescreen 16:9 footage at the same time on the HD's and the Sky cam (like, a tape in each cam). Anyone brave enough can then edit up some 16:9 with sound from our digital copies and from VTA/VTB (whichever one ends up serving the mainstage), the sets from this year are then usable whatever happens next year...
  • Sky cam location, your location seems good Malcolm, - i'd forgotten about the trees! , Can you slap that into the notes section?
  • I'd say more now, but apparently I have some "jeff" acting to do for Manm Man at 10am... as long is it doesn't involve jam!

Video Path

Sources

Main Stage only

HD 1 (stage)

HD 2 (stage)

HD 3 (stage)

Howard (stage)

Sky Cam (V139)

Canon (balcony)

VT PC (control room)


Indoor Stage only

MS5 1 (stage)

MS5 2 (stage)

Small Cam (for drummer etc) (on stage)

Smallish Cam (back of hall)

VT PC ? (control room)


Destinations

Main Stage broadcast

Main Stage Rack

  • VT 'P169'
  • Main DA
  • DaVE P169
  • DaVE

Main Stage DA (looking at the back, this is what the DA will look like)

DA 01 DA 02 DA 03 DA 04 DA 05 DA 06 DA 07 DA 08 DA 09 DA 10 DA 11 DA 12 DA 13 DA 14 DA 15
INPUT HD 1 HD 2 HD 3 Howard Sky Cam Canon (balcony) VT PC DaVE P169 A Out DaVE P169 B Out DaVE P169 C Out DaVE P169 D Out DaVE OUT Graphics SPARE SPARE
Output 1 VT P169 1 VT P169 2 VT P169 3 VT P169 4 VT P169 6 VT P169 7 VT P169 8 VT P169 5
Output 2
Output 3
Output 4 Prev Mon Prev Mon Prev Mon Prev Mon Prev Mon Prev Mon
Output 5
Output 6 DaVE P169 4 IN DaVE P169 6 IN DaVE P169 7 IN DaVE P169 8 IN STREAM
Output 7 DaVE P169 1 IN DaVE P169 2 IN DaVE P169 3 IN NO 7th OUT NO 7th OUT NO 7th OUT NO 7th OUT NO 7th OUT NO 7th OUT NO 7th OUT NO 7th OUT NO 7th OUT NO 7th OUT NO 7th OUT NO 7th OUT

All 7 inputs (listed above) into 7 sequential DA inputs.


An output from each of these seven will be fed into DaVE P169 (but omitting input 5 as it brightens the image).


Only use one of each pair of outputs from DaVE P169 (especially in the case of output 'B' as it struggles with both), feed each of these four into the DA, then one of these four DA outputs to a preview monitor, the other to DaVE itself.


Dave out into corriogen and the broadcast signal out. Broadcast into a DA and out to a preview monitor and also to a computer for world wide transmission.


Since VT 'P169' doesn't currently have a use, it could be used for controlling preview monitors. though this is a bit of a waste and there will probably be a better use. Also having preview monitors with variable sources could be confusing. Somtehing to think about later possibly.


Remember to put DaVE's B&B into VT P169


Preview monitors:

4 DaVE INs

DaVE Preview

DaVE Out?

Graphics Out (assuming we have graphics for ticker bar etc.)

Possibly Another four selectable from VT 'P169's eight inputs. These 8 inputs will probably be the 7 inputs to DaVE P169, and possibly graphics.


Indoor Stage broadcast

OB Trolley with very little alteration.

Use the 4->1 PIP and already-mounted monitor. Also have a monitor for the main out and one for VT PC, or whatever equivalent is dedicated to the indoor path.

Inputs to the DA:

  • Wide
  • Stage Left
  • Stage Right
  • Switch (VT PC / Drummer)
  • VT PC (or equiv)
  • Max Out (even if Max duplicates its output, which I don't think it does, the preview should be as late in the path as possible)


Main Stage DA (looking at the back, this is what the DA will look like)

DA 01 DA 02 DA 03 DA 04 DA 05 DA 06
INPUT Wide Stage Left Stage Right VT PC / Drummer VT PC MAX Out
Output 1 4-1 PIP 4-1 PIP 4-1 PIP 4-1 PIP Prev Mon Prev Mon
Output 2
Output 3 Max 1 Max 2 Max 3 Max 4 VT / Drum Switch STREAM
Output 4

(Only Four outputs and one loop thru I think)

Cable Runs

Main Stage:

  • Sky Cam (V139):
    • Trail cable out of V120, across balcony (NB the boardswhich make up the floor of the balcony may accommodate the BNC nicely, alternatively weave it in the rails. Loop cable around window frame, secure to tripod and plug into camera. Camera running off mains power from somewhere in V139, may require a medium length extension lead.
  • Howard (marquee roof):
    • BNC from howard, taped to howard and secured to frame, not dangling from socket. This trails down whichever side of the frame is most convenient, and probably goes into a video over cat5e box. Also needs power over 4-pin XLR, and control over cat5 to go all the way to the roof.
  • Three HD Sonys
    • Umbilical to each camera, secured to the camera/tripod to put as little strain on socket as possible, possibly also have s-vid bodge(s) and cable ties or tape nearby in case on of the sockets goes faulty. Video from at least two, probably all three into a video over cat5 box.

Balcony

  • Two xlrs, one for the omnidirectional caged mic, the other for the rifle mic or cardioid as main stage sound backup.
  • Comms for presenter (the camera op should know what they're doing, and can receive cues from the V120 window).
  • Non-Firewire Canon
    • BNC for camera, from V120, to balcony railings, into breakout cable and Camera.

Indoor Stage

Cat5 doing either 3 or all 4 cameras from the hall to the control room BNC if necessary should go on the wide shot camera (more reliable than over cat5). IFF the mains-powered 3vid over cat5 box is used, I'd suggest having a BNC from eacho f the three cameras near the stage running to the cat5 box at the back of the hall, reduces chance of damage to cable, makes alterations/bodges easier.

Mains to power cameras, I haven't specifically asked for this but there shouldn't be a shortage of power, given all the mains sockets on the walls anyway.

All indoor stage video cables to V122

CAT5 ADAPTORS

Will probably have the powered one in the hall, and the passive one on the main stage. This will of course only work if the passive one can send a decent signal all the way to V120 from the main stage. The distances to the two stages are about equal.

  • Advantages:
    • Powered one receives three signals, we have three cameras on indoor stage, one cat5 to back of hall and out of window towards V122 (avoids having three bncs running across the hall, saves cable length, simplifies run, fewer potential fault points etc.).
    • Main Stage is more important, the passive sender sends one signal on each pair, they're completely isolated as far as I (Malcolm) know. If one pair develops a problem we still have three good camera signals being sent along the cat5.
    • Is bidirectional, the monitors at the main stage will receive signal, uses one of the less-reliable and lower-quality cat5 pairs rather than a BNC for low-priority monitors.
  • Disadvantages
    • May not be powerful enough to send signal, would prefer signal from mains stage to be good.

More to follow...


Comms

Mostly still to write down.


Main Stage Monitors

Still to write.