G/046 Lighting Rig

Revision as of 19:08, 8 January 2013 by Robert.walker (talk | contribs)

Power

The rig eats a lot of juice: It is fed from two 32amp Ceeform plugs on the wall (same wall as fire escape). According to the Mains Circuits page, both are on the Yellow Phase.

Dimmers

Strand 6pack Dimmer

  • DMX512 control via 5pin XLR. Pass Through
  • 6 10A channels, each with dual 15A sockets
  • 32A Power Cable


Eurolite DPX-405: (1 of)

  • DMX512 control Via 3pin XLR. Pass Through.
  • 4 5amp channels each.
  • IEC sockets out.
  • No Preheat.
  • 13a Plug currently.


Double clunky 13a: (1 of)

  • 2 13a channels each (MAX 2.5Kw each)
  • 13a in and out for each channel
  • Sliders / pots for control
  • Max & min adjust (you'll need a flat screwdriver)
  • Very useful on OB's. Don't hesitate to bring it!

Desk

Strand 200 plus see Lighting Desk

Hardware

  • On the ceiling is a home-made steel pipe frame, with some IWB's here and there (IWB's not connected).
  • More pipe clamps, lamp clamps in box under lighting desk.

Cables

Usually found on top shelf in techie room

  • 15a -> IEC
  • Various lengths of 15a
  • UK 13a ->15a adaptors (2 of)
    • Very useful on OB's

Patching

  • IEC Panels feed the plugs on the ceiling.
  • IEC leads from dimmers. MAX 5a (1Kw).

Lights

Furse fresnels: (2 of)

  • Old fresnels.
  • No barndoors
  • TUNGSTEN


Selecon Asymetric floods: (2 of)

  • Not old! - still incredibly popular as of 01/10
  • Asymetric! not even spread of light. spread gets better, the further they are from the wall. Remember, big side at bottom.
  • Use to light back walls evenly, rather than a large "splodge" of light at the top, and not much at the bottom.
  • The above makes them very useful when doing Chroma keying work.
  • Lamp access by flipping the catch on top - whole fornt of fixture is hinged to allow lamp change without re-focusing.
  • Colourframe located by flipping open the cover at the top. Not the catch! Slide out colourframe from top.
  • No Barndoors (selecon do still sell them though)
  • TUNGSTEN 500w


Selecon Symetric Floods: (1 of)

  • As Asymetric, but even.
  • No colourframes.
  • No Barndoors (selecon do still sell them though)
  • TUNGSTEN 500w


Generic bar of 4 floods: (2 of)

  • normal floodlights
  • 3 functioning bulbs per bar.
  • DIY colourframes from gridding - bend to suit...
  • 300w / compartment
  • very god for OB's


Generic floods: (3 of)

  • normal floodlights
  • DIY colourframes from gridding - bend to suit...
  • 300w


Strand patt 123 Fresnels: (1 of)

  • The funny egg shaped ones.
  • No colourframes.
  • T17 / T1 lamp.
  • TUNGSTEN 1000w


Strand patt 743 Fresnels: (2 of)

  • Adjustment control at rear, and behind barndoors.
  • Rotating barndoors.
  • Colourframes in cupboard.
  • T19 / T11 lamp.
  • TUNGSTEN 1000w


Polaris Quartzcolor Pole-Op Fresnels: (2 of)

  • With rotating barndoors
  • adjust Pan, Tilt & Beam Via knobs.
  • Colourframes - the octagonal ones. in cupboard.
  • Rotating barndoors.
  • HALOGEN 1000w
  • These are more "orange" than tungsten, so bear that in mind when colour balancing...


Par 64 Floor cans: (6 of)

  • Black
  • all with Gel frames
  • MF lamps
  • 500w Tungsten
  • Please only use HT gels, as they make an awful stink!

Gels

Colours

  • Blues
    • Lee 132 (medium blue)
    • Lee 118 (Light Blue)
      • Nice for set boards/uplighting...
    • Lee HT* 079 (just Blue)
    • Rosco 65 (pale blue)
    • Lee 117 (steel blue)
    • Lee 172 (Lagoon blue)
    • Unknown dark blue, marked as "199" (probably Lee regal blue)
  • Reds
    • Lee 106 (primary red)
  • Purples
    • Lee 049 (purple)
    • Unkown purple (possibly congo blue lee 181, looks like UV - but isn't really)
  • Greens (inc turquoises)
    • Unkown green (various & dark)
    • HT* 122 (Fern Green)
    • HT* 115 (Peacock Blue, yes it isn't really blue)
      • This works really well for backlighting set-boards.
  • Pinks
    • Rosy Pink (not much)
    • Lee 148 (Bright Rose)
    • Lee 345 (Fuschia Pink)
      • This is stronger than you'd think
  • Yellows
    • yellow straw(not much)


Diffusions & scrims

  • Scrim - looks like tracing paper, but made of plastic and not nearly as flamable. Like gels, will melt if touching the glass of a flood. Use this to soften light - you can also put over only some of the fixture (called half scrim) to soften light e.g near to the source only. Very useful, but underused.


Colour Temperature Filters

  • 1/2 CTB. Lee 202 or eqiv. Looks grey. decreases output of lower CT's (orangeyness reduction). Makes thing noticeably dimmer. ** tungsten (3200K) to daylight (4300K)
  • 1/4 CTB less strong CTB.

Signal

DMX

  • Chamsys MagicDMX as control
  • 120ohm terminator in back of last unit in DMX chain
    • currently Eurolite DPX-405
  • UVI remux in construction.

Analogue

  • Desk output channels 1-24 in 0-10v on DB-25 connector. Adaptor cable goes to DINS.


spare lamps

Spare lamps are hidden at the back right of the cupboard.

  • K1 Lin 500w (x4)
  • T18 (x2)
  • T17 (x1)

LD toys

Swatch books

These are on the lighting desk table.

  • Lee designer colour order - 02/2010 version
  • Gam designer colour order - 02/2010 version
  • Rosco supergel - 02/2010 version
  • Rosco Lux - 02/2010 version


other stuff

  • chinagraph pencils for writing silly (and possibly useful) messages on gels.

Old/unused Equipment

This is equipment that is still owned by YSTV and is stored within the studio, but is not currently in use due to newer equipment/incompatibility with current equipment in use.

Pulsar status dimmers: (2 of)

  • 8-pin Din analogue signal in, 0-10v
  • With pre-heat (good for not shocking cold bulbs if they suddenly get turned on, this increases lamp life.
  • 6 5amp channels each.
  • IEC plugs on flying leads out.
  • If they're buzzing, they're happy!
    • faults
      • Top dimmer channel 3, Likes to turn itself on to around 30% after a while. i.e. It's level can be raised, but not lowered beyond 30%. The time taken for this fault to appear can be minutes, or hours. It does not seem to be linked to heat - on 18/02/2010 the behaviour was observed when warm, and cold (given a break for 1/2 hour before retrying). This dimmer channel corresponds on the desk to what was "old channel I" - i.e. pre 18/02/2010 it would have been bottom dimmer channel 3..
      • Bottom dimmer channel 3, The transistor/triac looks fried and has continuity between the emitter and collector, also two medium-power 270 Ohm resistors have physically split. This dimmer channel corresponds on the desk to what was "old channel C" - i.e. pre 18/02/2010 it would have been top dimmer channel 3..
      • One dimmer is without a power cable - this was due to power cable being needed for the Strand 6pack


Zero88 Sirius24 (2 of)