tick.png HD OK

ATEM 1 M/E is the name of two Blackmagic Design vision mixers used by YSTV. The ATEM 1 M/E Production Switcher was originally purchased in Autumn 2013 as part of the HD upgrade, and served as the station's vision mixer until Summer 2015. The ATEM 1 M/E Production Studio 4K is a newer model of ATEM 1 M/E which was purchased in Summer 2015 following a generous donation by Greg Dyke. It replaced its earlier incarnation as YSTV's studio vision mixer, while the original model was put to use in Kenobi.

Production Studio 4K (Studio)

 
Production Studio 4K

The Production Studio 4K is a 1U, half-depth vision mixer. It has many improved features over its predecessor, including a significantly increased number of SDI inputs and outputs, better cooling, and front panel display and controls - allowing the switching of the three auxiliary outputs.

Connections

 
Connections

Inputs

The studio ATEM has the following video inputs:

  • 10 6G-SDI - capable of up to 4K resolutions (whether it meets UHD specs is yet to be seen)
  • 1 HDMI - replaces the first SDI input

This allows for a total of 10 simultaneous inputs.

All inputs must be of the same format (which is set within the ATEM Control Software) otherwise the input will not be shown. As our Sony cameras can only output either 1080i50 or 576i50, we are limited to one of these formats for the entire vision path.

The ATEM also has both an XLR and phono stereo pair for external audio input.

Outputs

The studio ATEM has the following outputs:

  • 2 6G-SDI, 1 3G-SDI program - totalling 3 program outputs capable of 1080i
  • 1 HDMI program
  • 1 HD-SDI Multiview
  • 1 HDMI Multiview
  • 1 6G-SDI Preview
  • 3 6G-SDI Auxilary

The ATEM also features an XLR stereo pair for external audio output.

Production Switcher (Kenobi)

 
Production Switcher

The Production Switcher is a 2U vision mixer. It is notable for its minimal depth and external heatsink. While not carrying as many inputs as the newer model, it does feature both analogue input and output, making it much more compatible with older pre-HD devices.

Connections

 
Connections

Inputs

The OB ATEM has the following inputs:

  • 4 HDMI
  • 4 HD-SDI
  • 1 Analog (composite, s-video or component switchable) - replaces the first HDMI input

This allows for a total of 8 simultaneous inputs.

The ATEM also has an XLR stereo pair for external audio input, on a breakout cable.

Outputs

The OB ATEM has the following outputs:

  • 1 HD-SDI program
  • 1 SDI program
  • 1 Analog composite
  • 1 HDMI program
  • 1 HD-SDI Multiview
  • 1 HDMI Multiview
  • 1 HD-SDI Preview
  • 3 HD-SDI Auxilary
  • 1 Analog Component

The ATEM also has an XLR stereo pair for external audio output, on a breakout cable.

Control

The control software that shipped with the ATEM is stored on the software drive. Blackmagic regularly release updates for both the control software, which include updates to ATEM firmware.

ATEMs can be controlled by any version of the control software lower than its firmware version. However, newer control software will prompt the user to update the ATEM firmware.

Fun Stuff

Media pool

The ATEM's media pool has 32 still image windows and 2 clip windows that also have a location for audio. Most common image formats can be loaded into the pool. Clips are comprised of sequences of TGA images, which get played back at 25 fps. At 1080i, a maximum of 180 frames can be loaded onto the ATEM at any one time (about 7 seconds) - this number is shared between the two clips.

Stingers

Stingers are a type of transition the ATEM can use to switch between inputs - usually in the form of a short animation. They typically fill the screen, making the transition unnoticeable.

If creating your stinger in After Effects, you should use the render queue to generate the TGA sequence. This frame is not enabled by default so select 'Window' from the top menu, and then 'Render Queue' to enable it. Drag your composition into the render queue (if it isn't already), the click on the small arrow below labeled 'Output Module'. Choose 'Custom', and a dialog menu should appear. The format should be 'Targa Sequence', and the video output should be 'RGB + Alpha'. Click OK, then choose an output location using the dropdown menu in the render queue. Finally, click 'Render', and your composition will be rendered as a sequence of TGA images.

It's best to work in 25 fps from the start, as the TGA sequence will render at whatever the frame rate of your composition is. Be sure your composition starts and ends with nothing visible on screen, with a transparent background.

A stinger can easily be setup using the ATEM control software. First, import your animation as a TGA sequence into the media pool, drag all the images into one of the two media players, and add any accompanying audio. Then, in the main mix window, open the 'Transition' module and select the Stinger icon. From here you can select which media player to use for the stinger, how long it lasts for, and when to fade between the two inputs.

 
ATEM control software

To perform a stinger transition, select STING, and then AUTO as normal. To change the transition back to a fade, select MIX.

External links