|
|
| (6 intermediate revisions by 2 users not shown) |
| Line 1: |
Line 1: |
| =='''Zero88 sirius 24'''==
| | #REDIRECT [[Strand 200+]] |
| * Analog (0-10v)
| |
| * 24 channel
| |
| * 2 preset
| |
| * 99 memories
| |
| * 99 chases
| |
| ** each of 99 steps
| |
| * Output via DB25
| |
| * '''Two of them'''
| |
| ** The chaser section on the keyed desk one doesn't respond.
| |
| | |
| | |
| ==The On button!==
| |
| Only turn the desk on or off when all the dimmers are off - the desk flashes everything to 100%, and if the bulbs are cold, you'll shorten their lives...
| |
| The button is on the back of the desk, on the right.
| |
| | |
| | |
| ==Help! it's broke!==
| |
| * No it isn't.
| |
| * Desk plugged in?
| |
| * On switch?
| |
| * DBO switch?
| |
| * Masters?
| |
| * Control cables in right dimmer sockets?
| |
| * Dimmers on?
| |
| * Dimmer electronics & preheat on?
| |
| * Dimmer outputs plugged into right patchbay place?
| |
| * Lights in correct ceiling sockets?
| |
| ** Diagram on wall - check that?
| |
| * Get help.
| |
| | |
|
| |
| ==Master section==
| |
| * Grand Master
| |
| ** overall control of desk, when this is down, nothing comes on.
| |
| * DBO
| |
| ** It's a flicky switch for cutting everything off
| |
| **'''Don't''' play with it - if it breaks in OFF, then you've had it!
| |
| * Each row of faders has a master (with matching colour!)
| |
| * Flash master
| |
| ** when in RUN mode and "flash" is set to ''flash'' the buttons under each row of faders cause those respective items to go to 100%
| |
| ** The flash master controls the maximum value of the flash..
| |
| * Chaser master
| |
| ** controls the level of the chase
| |
| | |
| | |
| ==Basic States==
| |
| * Push everything Down
| |
| * Desk in Run Mode
| |
| * Grand master up
| |
| * Preset master up (you choose which)
| |
| * Twiddle corresponding coloured rows faders, things happen.
| |
| | |
| | |
| To set a different preset (one per row), leave everything as it is
| |
| * Push the other preset master up, and the old one down
| |
| * Twiddle other row of faders.
| |
| | |
| | |
| ==Programming memories==
| |
| The Zero88 desk allows you to pre-configure your lighting using memories. Heres how to program a memory:
| |
| * Using the Dial or keyswitch, put the desk into Program mode. (shown with red L.E.D on sides of dial / keyswitch).
| |
| * Set all the sliders to 0. Zero.
| |
| * Pull up the grand master(the very bottom, right slider).
| |
| * Pull up the "B" Master (The "presets" fader with the same colour as those of the 2nd top line of faders - red or blue.)
| |
| * Make sure you are using the 2nd row of presets for the above instruction. NOT doing this will mean all your states to be programmed won't be programmed!
| |
| * Set the required lighting state - fiddle with 2nd row of sliders until all looks good. etc.etc.
| |
| * On the lower part of the Desk, there are memory buttons. use them to select the memory you want to program - (1 to 99).
| |
| * are you sure you like that lighting state? OK, hit (gently!) the "program memory" button.
| |
| * Job done.
| |
| | |
| | |
| ==Transferring a memory to a "manual master"==
| |
| * In program mode.
| |
| * choose the appropriate memory using memory up & down buttons.
| |
| * slide fully up, the "manual master" you want to transfer to...
| |
| * press that slider's "transfer".
| |
| * the memory you transferred's number will appear for that "manual master"'s fader.
| |
| * Job done. Test it by leaving all sliders down apart from grand master & that "manual master" - if lights are on, good! if not, try again!
| |
| | |
| | |
| ==Manual==
| |
| * stapled together paper manual from Zero88 is ontop of dimmer rack.
| |
| * Zero88 have a copy, which is available at http://common.zero88.com/public/files/siriusmk1.pdf
| |
